MSF: Two dropped object incidents

  • Safety Flash
  • Published on 12 February 2024
  • Generated on 29 April 2025
  • IMCA SF 03/24
  • 3 minute read

While pulling a pin out, the metal wedge in place was dislodged and fell between the gangway components, 13m to the deck below.

Incident 1 – dropped metal wedge

A pin was required to be pulled on a hinge system for the dynamic gangway system on a W2W (walk-to-work) vessel. As part of this task metal wedges were used to hold some of the gangway components in place. The job of pulling the pins was not going as expected due to space limitations, the effects of surface corrosion on the pins and the chosen method of pulling the pins. While pulling the pin out, the metal wedge in place was dislodged and fell between the gangway components, 13m to the deck below.  No-one was underneath the gangway at the time. MSF Safety Alert 23-17.

Dropped object incidents
Dropped object incidents

What went wrong?

  • The metal wedges did not have a place to secure a tethering device.
  • The method chosen to pull the pin was not optimal.
  • Not all the tools could be secured from dropping and there was no collective dropped object arrest system to catch smaller tools or items.
  • The aft area around the gangway was not fenced off and personnel could have walked underneath the drop zone.
  • Simultaneous operations were taking place in the area on deck around the gangway and there was a risk of someone accidentally walking into the DROPS zone.

Actions taken

  • Modified the metal wedges to accept a tethering device.
  • Investigated how a collective dropped object arrest system such as a net could be installed under the gangway for future work.
  • Identified an optimal solution for pulling the pins on gangway.
  • Improved guidance and training for personnel on barriering-off areas in a DROPS zone.    

Incident 2 – Dropped Lightning Rod

A lighting rod conductor mounted on top of a dynamic gangway tower for a Walk-To-Walk vessel was found lying on the deck below the tower. No personnel onboard the vessel observed or heard the object fall. 

The potential for serious injury existed due to: 

  • The location of the dropped area (deck is frequented by personnel)
  • The weight of the object (1.5kg) and the distance it fell (26m).

What went wrong

There was no obvious damage to the rod or fittings, it is assumed that the fittings loosened / unscrewed over time. The incident presents immediate causes such as:

  • Impact of rough or bad weather on the rod securing connections.
  • Lack of inspection/maintenance on the securing of the rod.
  • Design deficiency in terms of a secondary securing mechanism for the rod.

Actions taken

  • Ensure checking of lightning rod conductor fittings and other similar fittings such as lights, cameras, wind sensors etc are included in planned maintenance schedule.
  • Install a secondary securing mechanism where necessary.  

Latest Safety Flashes:

Fatality following a fall from a wind turbine

The Scottish Courts and Tribunals Service, and UK HSE, has published a response to a fatal incident in which a crew member fell to their death.

Read more
UK HSE: Risk of collision with offshore installations from attendant vessels

The UK Health and Safety Executive (HSE) has published Safety Notice ED01-2025 relating to the risk of collision with offshore installations.

Read more
USCG: Hazardous Zone Markings and Safety Protocol Awareness

The United States Coastguard has published Safety Alert 04-25 relating to the importance of Hazardous Zone Markings and Safety Protocol Awareness.

Read more
BSEE: Crane safety awareness during offshore helideck operations

BSEE published Safety Alert 491 relating to a the investigation of a near miss crane incident on an offshore platform.

Read more
Incidents occurring during decommissioning

IMCA has put together a summary of incidents relating to decommissioning.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.